Description
Atmels SAM3S series is a member of a family of 32-bit Flash
microcontrollers based on the high performance ARM Cortex-M3
processor. It operates at a maximum speed of 64 MHz and features up
to 256 Kbytes of Flash and up to 48 Kbytes of SRAM. The peripheral
set includes a Full Speed USB Device port with embedded
transceiver, a High Speed MCI for SDIO/SD/MMC, an External Bus
Interface featuring a Static Memory Controller providing connection
to SRAM, PSRAM, NOR Flash, LCD Module and NAND Flash, 2x USARTs, 2x
UARTs, 2x TWIs, 3x SPI, an I2S, as well as 1 PWM timer, 6x
general-purpose 16-bit timers, an RTC, an ADC, a 12-bit DAC and an
analog comparator.
Features
• Core
– ARM® Cortex®-M3 revision 2.0 running at up to 64 MHz
– Memory Protection Unit (MPU)
– Thumb®-2 instruction set
• Pin-to-pin compatible with AT91SAM7S series (48- and 64-pin
versions)
• Memories
– From 64 to 256 Kbytes embedded Flash, 128-bit wide access, memory
accelerator, single plane
– From 16 to 48 Kbytes embedded SRAM
– 16 Kbytes ROM with embedded bootloader routines (UART, USB) and
IAP routines
– 8-bit Static Memory Controller (SMC): SRAM, PSRAM, NOR and NAND
Flash support
– Memory Protection Unit (MPU)
• System
– Embedded voltage regulator for single supply operation
– Power-on-Reset (POR), Brown-out Detector (BOD) and Watchdog for
safe operation
– Quartz or ceramic resonator oscillators: 3 to 20 MHz main power
with Failure Detection and optional low power 32.768 kHz for RTC or
device clock
– High precision 8/12 MHz factory trimmed internal RC oscillator
with 4 MHz default frequency for device startup. Inapplication
trimming access for frequency adjustment
– Slow Clock Internal RC oscillator as permanent low-power mode
device clock
– Two PLLs up to 130 MHz for device clock and for USB
– Temperature Sensor
– Up to 22 peripheral DMA (PDC) channels
• Low Power Modes
– Sleep and Backup modes, down to 1.8 µA in Backup mode
– Ultra low power RTC
• Peripherals
– USB 2.0 Device: 12 Mbps, 2668 byte FIFO, up to 8 bidirectional
Endpoints. On-Chip Transceiver
– Up to 2 USARTs with ISO7816, IrDA®, RS-485, SPI, Manchester and
Modem Mode
– Two 2-wire UARTs
– Up to 2 Two Wire Interface (I2C compatible), 1 SPI, 1 Serial
Synchronous Controller (I2S), 1 High Speed Multimedia Card
Interface (SDIO/SD Card/MMC)
– Up to 6 Three-Channel 16-bit Timer/Counter with capture,
waveform, compare and PWM mode. Quadrature Decoder Logic and 2-bit
Gray Up/Down Counter for Stepper Motor
– 4-channel 16-bit PWM with Complementary Output, Fault Input,
12-bit Dead Time Generator Counter for Motor Control
– 32-bit Real-time Timer and RTC with calendar and alarm features
– Up to 15-channel, 1Msps ADC with differential input mode and
programmable gain stage
– One 2-channel 12-bit 1Msps DAC
– One Analog Comparator with flexible input selection, Selectable
input hysteresis
– 32-bit Cyclic Redundancy Check Calculation Unit (CRCCU)
– Write Protected Registers
• I/O
– Up to 79 I/O lines with external interrupt capability (edge or
level sensitivity), debouncing, glitch filtering and on-die Series
Resistor Termination
– Three 32-bit Parallel Input/Output Controllers, Peripheral DMA
assisted Parallel Capture Mode
• Packages
– 100-lead LQFP, 14 x 14 mm, pitch 0.5 mm/100-ball TFBGA, 9 x 9 mm,
pitch 0.8 mm
– 64-lead LQFP, 10 x 10 mm, pitch 0.5 mm/64-pad QFN 9x9 mm, pitch
0.5 mm
– 48-lead LQFP, 7 x 7 mm, pitch 0.5 mm/48-pad QFN 7x7 mm, pitch 0.5
mm
